Get free quotes

Free tool

Before you buy new mags, check where they will sit

Enter the width and offset (ET) of your current wheels and the new ones. The calculator shows how far the inner edge moves towards the suspension and how far the outer edge moves out towards the arch.

A set of new alloy wheels stacked in a wheel supplier's showroom

Compare wheel width and offset

Current wheel
New wheel

Current New, seen from the front, to scale

Where the new wheel sits

Inner edge (towards strut)
–
Outer edge (towards arch)
–
Track width, per axle
–
Backspacing, current
–
Backspacing, new
–

Two wheels with the same diameter can sit in very different places on the car. The rim width and the offset decide where: a lower offset or a wider rim pushes the face out towards the arch, a higher offset pulls it in towards the strut and brakes. Getting it wrong means rubbing tyres, a wheel that touches the brake caliper or a face that sticks out past the bodywork.

What offset and ET mean

Offset is the distance in millimetres from the centre line of the rim to the face where the wheel bolts onto the hub. It is stamped on the wheel as ET followed by a number, for example ET35, often next to the size, such as 7J x 17.

  • Positive offset (ET35): the mounting face is towards the outside of the wheel, so the wheel sits further in. Most front wheel drive cars use this.
  • Zero offset (ET0): the mounting face is on the centre line.
  • Negative offset (ET-12): the mounting face is behind the centre line, so the wheel sticks out. Common on lifted 4x4s and bakkies.

Reading the result

The calculator works out where the inner and outer edges of the rim sit compared with your current wheel. Inner clearance is what matters for the strut, the spring and the brake caliper: if the new inner edge moves in by more than the gap you have now, it will touch. Outer position, often called poke, is what matters for the arch and the bodywork: if it moves out, the tyre can rub the arch lip on bumps and full lock.

Measure your current gaps with the car on level ground: from the inside of the tyre to the strut, and from the outside of the tyre to the arch lip. Then compare them with the change shown. Leave a margin of a few millimetres for the tyre bulging under load and for suspension movement.

Other things that must match

Offset is only one of the numbers. The wheel must also have the right stud pattern (PCD), a centre bore that fits the hub or the right hub centring rings, enough clearance for the brake caliper behind the spokes, and wheel nuts or bolts with the correct seat. A wheel supplier should check all of these against your vehicle before you pay.

Frequently asked questions

Can I use spacers to correct the offset?
Spacers move the wheel out, which is the same as lowering the offset. They need longer studs or bolts and must be hub centric and good quality. Many workshops prefer a wheel with the right offset to begin with. Check with your insurer, and have the wheel nuts re-torqued after the first drive.
What is backspacing?
Backspacing is the distance from the mounting face to the inner edge of the rim, measured in inches, and is mostly used for 4x4 and American style wheels. It describes the same thing as offset from the other side. The calculator shows an approximate backspacing using a half inch flange on each side.
Does offset affect handling?
Yes. Moving the wheel out widens the track and changes the scrub radius, which can make the steering heavier, more sensitive to ruts and harder on wheel bearings. Small changes are usually fine; large changes are worth discussing with an alignment centre.

Related services

Free quote request, no obligation

Request mag wheels quotes

Fill in the job card the way a wheel shop would: what is wrong, the wheel size and finish or the vehicle, where you are and how soon. Repairers, tyre shops and suppliers in your area quote you directly.

Job card No. 64772Mag Wheels and 4x4 Rims

1The job

2How many (optional, it helps the quote)

Your order

-
-
-
-
-
-
Estimate
-

A rule of thumb, not a quote.

3Stage, condition and timing

4Your list (optional)

  1. 01
  2. 02
Up to 12 lines: wheels, tyres, vehicles, machines or supplies.
Needs and options

5Your details

Free and no obligation. By sending you agree that we may share your request with suitable repairers, tyre shops and suppliers. See our privacy policy.

Get free wheel repair quotes