Get free quotes

Free tool

Work out the stud pattern before you buy wheels

Count the studs and measure from the centre of one to the centre of the next. The calculator works out the pitch circle diameter (PCD) and the nearest standard pattern.

Chrome wheel nuts and a locknut key next to an alloy wheel

Measure the stud pattern

The measurement you entered

Your stud pattern

Pitch circle diameter
–
In inches
–
Closest standard pattern
–
Difference
–

PCD, the pitch circle diameter, is the diameter of the imaginary circle through the centres of the wheel studs or bolt holes. It is written as the number of studs and the diameter in millimetres, for example 5 x 114.3. A wheel only fits if both numbers match the hub exactly; patterns that are close, such as 5 x 112 and 5 x 114.3, are not interchangeable.

How to measure the PCD

With the wheel off, or on the wheel itself:

  • Count the studs or bolt holes.
  • Measure from the centre of one stud to the centre of the stud right next to it. A ruler or a vernier works; measuring from the left edge of one hole to the left edge of the next gives the same distance.
  • Enter both in the calculator. It uses the geometry of the circle to work out the PCD.

On a 4, 6 or 8 stud pattern you can also measure straight across, from the centre of one stud to the centre of the stud opposite: that distance is the PCD.

Inch and millimetre patterns

Some patterns are given in inches. 4 x 4.5 inch is 4 x 114.3 mm, 5 x 4.5 inch is 5 x 114.3, 5 x 5.5 inch is 5 x 139.7 and 6 x 5.5 inch is 6 x 139.7, the pattern used on many bakkies and 4x4s. The calculator shows both.

PCD is not the only fit

A wheel with the right PCD can still be wrong for the car. Check the centre bore (the hole in the middle that locates on the hub), the offset, the clearance for the brake caliper and the seat of the wheel nuts or bolts: conical, ball or flat. A wheel that bolts on but does not sit on the hub can vibrate and loosen. Your vehicle handbook, the dealer or a wheel supplier can confirm the specification.

Frequently asked questions

Can I fit 5 x 112 wheels on a 5 x 114.3 hub?
No. The difference of about a millimetre on each stud means the nuts cannot seat properly, and the wheel can work loose. Use wheels made for your pattern. Adapters exist, but they move the wheel out and need careful fitting.
Where can I find my PCD without measuring?
In the owner's manual, on some wheels stamped inside the barrel, or from a dealer or wheel supplier with your vehicle's model and year. Measuring is a good check, because previous owners sometimes fit wheels with adapters.
Why does my measurement not match a standard pattern exactly?
Measuring to the centre of a stud by eye is rarely perfect, so a result within a millimetre or so of a standard pattern usually points to it. If the result falls between two close patterns, measure again with a vernier or ask a tyre shop to check with a PCD gauge.

Related services

Free quote request, no obligation

Request mag wheels quotes

Fill in the job card the way a wheel shop would: what is wrong, the wheel size and finish or the vehicle, where you are and how soon. Repairers, tyre shops and suppliers in your area quote you directly.

Job card No. 64772Mag Wheels and 4x4 Rims

1The job

2How many (optional, it helps the quote)

Your order

-
-
-
-
-
-
Estimate
-

A rule of thumb, not a quote.

3Stage, condition and timing

4Your list (optional)

  1. 01
  2. 02
Up to 12 lines: wheels, tyres, vehicles, machines or supplies.
Needs and options

5Your details

Free and no obligation. By sending you agree that we may share your request with suitable repairers, tyre shops and suppliers. See our privacy policy.

Get free wheel repair quotes